R&D

R&D

MFI TEST DEVICE
MFI TEST DEVICE
The mass flow index of the input and final products in the form of granules is measured according to the determined test parameters. In addition, the volumetric flow rate can also be measured. Tests can be analyzed at time/position settings at 50-450 °C.
detail →
DRYING-OVEN
DRYING-OVEN
The maximum operating temperature of drying-oven is 250°C. HOTSET, oil resistance, thermal aging, hydrocarbon resistance, dimensional stability tests which need the constant temperature can be carried out. Other oven is used for drying glass materials
detail →
ELONGATION AND TENSILE TEAR TEST DEVICES
ELONGATION AND TENSILE TEAR TEST DEVICES
Strip samples are prepared in the required thickness within the scope of the ISO 60811 standard with sample in granule form by laboratory-sized extruder in accordance with ISO 527, ASTM D 1938 and BS 6469-99.1 test standards. Dumb-bell test samples are prepared by cutting band specimens with pneumatic press for strength and tear tests.
detail →
TGA
TGA
TGA is used in R&D studies and input product analysis. The percentage of mass loss based on temperature is determined with TGA. It is used to determine % moisture, volatility, degradation of test samples and impurities and to obtain data for R&D studies.
detail →
LOI
LOI
Test samples are prepared at specified size in ASTM D 2863 standard and put in the sample chamber. The minimum oxygen concentration required for the combustion of the test sample is determined after applying specified flame size and ignition time in the standard.
detail →
PARTICLE SIZE ANALYSIS DEVICE
PARTICLE SIZE ANALYSIS DEVICE
Particle size distribution analysis are performed by forming test methods for each powder raw product in accordance with ISO 13310 standard. Volumetric distribution, numerical distribution and surface area distribution of test samples can be measured by this device. It measures the distribution of particles in the size range of 10 nm - 3500 µm with laser diffraction technique. D(10),D(50),D(90),D(97) µm, below 2 µm (%) and many physical properties of raw materials can be measured.
detail →
FTIR
FTIR
FTIR is used to characterize organic and inorganik compounds in the wavenumber range of 7800-350 cm-1 in R&D studies and raw product analysis.The spectrum of each substance is recorded in the actual library. Comparison and verification studies are carried out. Content percentage of the raw materials which are indicated specifically are determined.
detail →
DSC
DSC
DSC is used in R&D studies and input product analysis. Parameters such as melting temperature, thermal decomposition temperature,etc of test sample are determined. Flash point and ignition temperature of test sample are considered when the maximum test temperature is selected
detail →
MOISTURE DEVICE
MOISTURE DEVICE
Moisture value of the raw and final products is determined as a percentage or ppm. Moisture test is performed with small amount of test sample so that moisture device can vacuum if the expected moisture value of the test sample is high. Calibration, vacuum operation and changing desiccant chemical substance are performed periodically in order that keep high accuracy of a measuring instrument.
detail →
DENSITY DEVICE
DENSITY DEVICE
The spesific density of raw and final products are performed in accordance with ASTM D 792 standard. Ambient temperature is kept at 23°C for density analyzes to be performed at 23°C. The spesific density value of Ethanol used in the analysis and liquid input product can also be measured.
detail →
MUFFLE FURACE
MUFFLE FURACE
Ash test of raw and final products are performed to determine percentage of the filler. Test temperature and duration vary depending on the chemical structure of the raw product.
detail →
VERTICAL COMBUSTION TEST CABIN
VERTICAL COMBUSTION TEST CABIN
UL94 Vertical combustion tests of the samples which are prepared from band samples are performed. The presence of burning drops and progress of combustion are controlled.
detail →
TÜRKÇE
R&D
R&D DEPARTMENT

R&D

MFI TEST DEVICE
MFI TEST DEVICE
The mass flow index of the input and final products in the form of granules is measured according to the determined test parameters. In addition, the volumetric flow rate can also be measured. Tests can be analyzed at time/position settings at 50-450 °C.
detail →
DRYING-OVEN
DRYING-OVEN
The maximum operating temperature of drying-oven is 250°C. HOTSET, oil resistance, thermal aging, hydrocarbon resistance, dimensional stability tests which need the constant temperature can be carried out. Other oven is used for drying glass materials
detail →
ELONGATION AND TENSILE TEAR TEST DEVICES
ELONGATION AND TENSILE TEAR TEST DEVICES
Strip samples are prepared in the required thickness within the scope of the ISO 60811 standard with sample in granule form by laboratory-sized extruder in accordance with ISO 527, ASTM D 1938 and BS 6469-99.1 test standards. Dumb-bell test samples are prepared by cutting band specimens with pneumatic press for strength and tear tests.
detail →
TGA
TGA
TGA is used in R&D studies and input product analysis. The percentage of mass loss based on temperature is determined with TGA. It is used to determine % moisture, volatility, degradation of test samples and impurities and to obtain data for R&D studies.
detail →
LOI
LOI
Test samples are prepared at specified size in ASTM D 2863 standard and put in the sample chamber. The minimum oxygen concentration required for the combustion of the test sample is determined after applying specified flame size and ignition time in the standard.
detail →
PARTICLE SIZE ANALYSIS DEVICE
PARTICLE SIZE ANALYSIS DEVICE
Particle size distribution analysis are performed by forming test methods for each powder raw product in accordance with ISO 13310 standard. Volumetric distribution, numerical distribution and surface area distribution of test samples can be measured by this device. It measures the distribution of particles in the size range of 10 nm - 3500 µm with laser diffraction technique. D(10),D(50),D(90),D(97) µm, below 2 µm (%) and many physical properties of raw materials can be measured.
detail →
FTIR
FTIR
FTIR is used to characterize organic and inorganik compounds in the wavenumber range of 7800-350 cm-1 in R&D studies and raw product analysis.The spectrum of each substance is recorded in the actual library. Comparison and verification studies are carried out. Content percentage of the raw materials which are indicated specifically are determined.
detail →
DSC
DSC
DSC is used in R&D studies and input product analysis. Parameters such as melting temperature, thermal decomposition temperature,etc of test sample are determined. Flash point and ignition temperature of test sample are considered when the maximum test temperature is selected
detail →
MOISTURE DEVICE
MOISTURE DEVICE
Moisture value of the raw and final products is determined as a percentage or ppm. Moisture test is performed with small amount of test sample so that moisture device can vacuum if the expected moisture value of the test sample is high. Calibration, vacuum operation and changing desiccant chemical substance are performed periodically in order that keep high accuracy of a measuring instrument.
detail →
DENSITY DEVICE
DENSITY DEVICE
The spesific density of raw and final products are performed in accordance with ASTM D 792 standard. Ambient temperature is kept at 23°C for density analyzes to be performed at 23°C. The spesific density value of Ethanol used in the analysis and liquid input product can also be measured.
detail →
MUFFLE FURACE
MUFFLE FURACE
Ash test of raw and final products are performed to determine percentage of the filler. Test temperature and duration vary depending on the chemical structure of the raw product.
detail →
VERTICAL COMBUSTION TEST CABIN
VERTICAL COMBUSTION TEST CABIN
UL94 Vertical combustion tests of the samples which are prepared from band samples are performed. The presence of burning drops and progress of combustion are controlled.
detail →
TÜRKÇE
R&D
R&D DEPARTMENT

R&D

MFI TEST DEVICE
MFI TEST DEVICE
The mass flow index of the input and final products in the form of granules is measured according to the determined test parameters. In addition, the volumetric flow rate can also be measured. Tests can be analyzed at time/position settings at 50-450 °C.
detail →
DRYING-OVEN
DRYING-OVEN
The maximum operating temperature of drying-oven is 250°C. HOTSET, oil resistance, thermal aging, hydrocarbon resistance, dimensional stability tests which need the constant temperature can be carried out. Other oven is used for drying glass materials
detail →
ELONGATION AND TENSILE TEAR TEST DEVICES
ELONGATION AND TENSILE TEAR TEST DEVICES
Strip samples are prepared in the required thickness within the scope of the ISO 60811 standard with sample in granule form by laboratory-sized extruder in accordance with ISO 527, ASTM D 1938 and BS 6469-99.1 test standards. Dumb-bell test samples are prepared by cutting band specimens with pneumatic press for strength and tear tests.
detail →
TGA
TGA
TGA is used in R&D studies and input product analysis. The percentage of mass loss based on temperature is determined with TGA. It is used to determine % moisture, volatility, degradation of test samples and impurities and to obtain data for R&D studies.
detail →
LOI
LOI
Test samples are prepared at specified size in ASTM D 2863 standard and put in the sample chamber. The minimum oxygen concentration required for the combustion of the test sample is determined after applying specified flame size and ignition time in the standard.
detail →
PARTICLE SIZE ANALYSIS DEVICE
PARTICLE SIZE ANALYSIS DEVICE
Particle size distribution analysis are performed by forming test methods for each powder raw product in accordance with ISO 13310 standard. Volumetric distribution, numerical distribution and surface area distribution of test samples can be measured by this device. It measures the distribution of particles in the size range of 10 nm - 3500 µm with laser diffraction technique. D(10),D(50),D(90),D(97) µm, below 2 µm (%) and many physical properties of raw materials can be measured.
detail →
FTIR
FTIR
FTIR is used to characterize organic and inorganik compounds in the wavenumber range of 7800-350 cm-1 in R&D studies and raw product analysis.The spectrum of each substance is recorded in the actual library. Comparison and verification studies are carried out. Content percentage of the raw materials which are indicated specifically are determined.
detail →
DSC
DSC
DSC is used in R&D studies and input product analysis. Parameters such as melting temperature, thermal decomposition temperature,etc of test sample are determined. Flash point and ignition temperature of test sample are considered when the maximum test temperature is selected
detail →
MOISTURE DEVICE
MOISTURE DEVICE
Moisture value of the raw and final products is determined as a percentage or ppm. Moisture test is performed with small amount of test sample so that moisture device can vacuum if the expected moisture value of the test sample is high. Calibration, vacuum operation and changing desiccant chemical substance are performed periodically in order that keep high accuracy of a measuring instrument.
detail →
DENSITY DEVICE
DENSITY DEVICE
The spesific density of raw and final products are performed in accordance with ASTM D 792 standard. Ambient temperature is kept at 23°C for density analyzes to be performed at 23°C. The spesific density value of Ethanol used in the analysis and liquid input product can also be measured.
detail →
MUFFLE FURACE
MUFFLE FURACE
Ash test of raw and final products are performed to determine percentage of the filler. Test temperature and duration vary depending on the chemical structure of the raw product.
detail →
VERTICAL COMBUSTION TEST CABIN
VERTICAL COMBUSTION TEST CABIN
UL94 Vertical combustion tests of the samples which are prepared from band samples are performed. The presence of burning drops and progress of combustion are controlled.
detail →